Search results

RE: Re: Exploded Diagrams of Axle Assemblies Thanks alot DOGHEAD. I had all apart, and it all seams simple,but I wanted to be sure I did not miss anything. Like everything else I do, I read directions after I am done to see how much I screwed up. Phil

Axel Single to Duel I cannotf pind the info to Reverse Hubs. Can anyone post it for me? I must go from Single to Dual wheels. Thanks, Phil

The only thing that stopped my M818 from running was Cracked fuel lines where the Switch is to switch from Left tank to Right tank. The hoses are Bent so sharply that they Kink. These are located Over tool box, to left of drivers seat. I disconnected mine and ran one strait line to L tank. Then...

I really don't know where we are heading in this wourld. Never mind the wourld, we better take hold at what is happening here in this country. For many years I have heard about Conserving energy. Here in N.H. I now hear they are going to Out Law Out Door Wood Furnaces. Here we are in a state...

JGRANT, can you make me one of those magnetics 3ftX6ft with the pics of THE WHITE House, and about 4 Grass Huts in front of it? I would like to put it on the side of my M750 TRL. before Election time.

Heck, we may have Deer come out in the pasture where I have my camper. I am told that 2 wild boar have been killed in the last 6 years or so. I do believe I saw one in the woods one day, but it was gone in seconds . Maybe a Moose in the same location, but the Fish Cops got an EVIL Eye out for ME!!

Scooter01922, why is your Deuce not ready? Did you not get a Runner when you bought it? Just kidding! I need an On-Off switch for my last Deuce. I got to see if I can install a tempo-rarry one. Phil

RE: Re: RE: Re: RE: Cucv as a daily driver Hey guys, I just got my 2nd M1008, from the same NG armory. I have noticed that the Camo paint on both trucks are a matched set! I never thought that the military actually use some kind of Pattern on these vehicles. Like someone said, "I learn...

Hey guys, where is everyone going to meet? I got a couple guys comming next week to look at equipment I am selling. I got a 3acre field with plenty of parking and firewood to keep warm and several hundred acres and lots more roads to go Rideing on. All is welcomed. Maybe a DEER can be shot to...

Hey Lifer, The first thing I always do to my purchases is Clear Coat them with Urethane, the wet look!!??? Looks Bitchen, don't it!!?? Yah, a little wet when I took the pics. Still wet today, Storm still comming up the New England coast.

I recovered a couple vehicles from Picatinny yesterday. The guys helped load me out and they were good at it. The M1008 started right uo and I had a driver with me to tow it back with my 2006 F150 with a tow bar I built the day before. All went well. The Deuce I got had no On Off switch. No...

DITO FMJ. Until item is in Hand, BE afraid!!

dm22630 hit the Nail on the head!! Notice that if U buy ONE item OR 100 items, it takes the same EUC and same amount of time. So why should GL even bother with the little guy, except that the Little guy will pay more for an Item than a Dealer, or Scrapper, or Exporter who buys in Quantities. We...

I got wheels from a Bolster trailer that can be used to lower it, 12:00 16.5

It may have a bad bearing, could be Loose belts.

There are many reasons to cause a vibration. Before spending any money, inspect it closely. Jack the vehicle up on all Fours, support with Jack stands and run it in 4x4. Get out and watch for Bent drive shaft, bent wheel or even bad Axel joints. Don"t run it at 80mph, just fast enough to watch...

It is built SPECIAL for OFF Road. Notice the BIG Axels. May have swapped axels from a M1008 with 4:56 gears. Biult to Bounce Well off Big Rocks!!

I see no reason why you cannot. Watch your RPMs and if you must, manually shift the trans to keep the RPMs up. I will be hauling a Deuce back from Picatinny on Thurs. with my 1ton Duramax and my 20,000lb Trl. I will also have another driver pulling an M1008 with my F-150 FORD!!?? I built a...

RE: Re: RE: Re: RE: Re: RE: my first CUCV m1009 has some pro I haven;t done it in a long tome. These motor mounts should be the same as regular gas job!??? Not totally sure. I have converted several Diesel to gas and all matched up. U must lift one side at a time just to release the weight on...

croatan kid, Are you putting the Cummins in a Deuce, or a GM truck? I did stuff a DT360 in a GMC I have here. It runs good and it is economical.