Search results

I have a Slow Leak in a tire, and I thought I would check it out!! I did have to remove the Govenor Cover on Trans and I found this convenient at the time. I did check out everything underneath and all is GOOD!!

Why do people buy in Al. and must trans. to Wi. , when you can buy in Wi. and less trave land ETC? I live in New England and I wish I could buy the Rust Free Vehicles in the west. South and or In Arizona, but I know the Hassel and cost of Transportation. I must buy as close to hame in order to...

I have bobed 1 deuce for a customer. I think it went well. First of all, do you need 10tires and wheels for what U are going to do? Then you actually lighten the weight, shorten the wheel base for better turning radius, and yes it rides much better and more effecient. You can Single it or keep...

Mikepop, I have had a Head ache since I have been collecting MVs. Maybe it is time to get rid of some!!?? I can take anything mechanical, but when it comes to electrical, and Exhaust systems, I do not LIKE!!

I had that problem with my 1009. The problem was the GRD. on the inside Socket itself. Quick repair was done. Good uck, Phil

RE: Re: RE: Re: RE: Re: RE: Pulling one wheel from the duals I changed about 24 tires and wheels with no impack wrench this week. I did lose One nut, somewhere in Lower left Abdowmen!!

RE: Tell me what I galeo7171, These 6.2 diesels are Loud! I bet if you check the Wing nuts on your air cleaner, they are loose. That would make a Barrel noise on top of engine. Also note after engine Warms up a while, it gets quieter. Just keep clean diesel and clean engine oil and it will keep...

This goes with Recovery4x4. It is hard to turn Bolt on Prim. filtrer. Take it off the frame, and by slightly bending fuel line, you can move filter back on frame by 4-6 ins.Drill holes for bolts to frame. This exposes Bolt and nut , easier to Change filter, it is not under Alt. . Phil

One more thing I do is use the Plates that hold the Torque rods in place . I use these under Diff. To put U-bolts throuhg. Use the with {OR} as Center Bolts. I would use Springs from a 21/2 ton trl. Much heavier and Bigger loads. I do understand most guys don't use Truck for work, so don't need...

I have done 1 bob Deuce. The way I will do my next one is to Cut Frame ahead of Boegies and behind it. Do not have to deal with Rivets. That is what is Time consuming and aggrivating. I cut exactly 36ins from my frame. So if you measure ahead of Boegies and behind, you have plenty to play...

I was wondering if anyone noticed any Axel Twist when using M105 springs, without the use of Torque rods. It may be OK if no amount of weight is carried, but with any weight there could be considerable twisting of axel and not so good on U-joints. Phil

I would still Check the S wire going to the starter. After what u went through, it could have Cooked it. Try Jumping with Screeewdriver on Starter. Good luck, Phil

Not sure on this one, but there are Adjs. for that on most steering boxs. Check it out before buying new.

Most simple and thorough inspection. Chock the truck so it does not roll in Neutral and with E brake off. Jack up a wheel, pull just the axel, see if there is greese on the outer bearing. If there is, most likely the inner BR. is OK. If dry, Pull bearings and inspect and Re- pack. Check for...

If you tried starting it with Low Batts. you have mare than likely Cooked the starter. From Day # 1, the all must have Good Batts. Between Glo plugs and Starter turning, there must be gooa AMPS. Even CIVY 6.2 have had this going on. Many times the starter will continue to Crank even when you...

It more than likely Over rev, and possibly OUT of Ballance{Loose Flywheel}

Preventive Maintanance!!It is always better to check things out at home, fix in and not have to make repairs on the Road.

RE: More ASV pics The Army will be shipping it to Iraq so they can have Target Practice with it and then Uncle Sam can purchase a Brand New One, to Stimulate the Economy!!!

The tires look nice!! Winch looks like it is HOLDING UP!! Wiper blades stiil on, but for how long!?? Nice Step, on Bumper. Is that a Bungy Cord holding the L- turn signal in place? Tarp is ON. Good Purchace!!

RE: Re: RE: Re: Exploded Diagrams of Axle Assemblies I have a Singled Deuce which I sold, and the guy wants Duels, so I must change them. This is A LOT of WORK!! I'll send some good pics later of another project. Phil