Search results

mikew, could you please fix this xm381 so we can open it and see it??? thanks

don't get to crazy with the torque wrench on the "U" bolts until after you take your truck to the scales. The springs are designed to support the front of the truck, with motor and all the rest up front. i would venture to say the rear of your truck will not weigh as much as the front with the...

i have a Printed 10 manual if you want it, the mag sensor probably got moved and is not close enough to give a reading, I was in the Supply NCO in one of the first units in FLARNG to get the A3 and don't remember the pioneer rack being installed, that being said, it will still fit in the...

you could do this and use two ropes on empty wheels as a winch if you didn't have one.

loosen the nut, get TWO 5 lbs sledge hammers and 1 good friend, and a new can of WD 40. spray liberal amounts on out side and in side, let sit for 10 minutes, start hitting lunette from both sides alternating strikes. should come loose. the lunette is a tapered fit, so after it starts to move...

after it is 72 inches. before it is front 72 rear 65??

the 14.00x20 will only fit the bob, like the 100dollarman said.

no, but you will have to cut down the run flat insert to fit. the bead on the 14.5x20 is 1.75 inches and the bead on the 14x20 is 2 inches. cut them down and mount them up. use a new o ring and you will be in business.

if you move the axle back 3 inches and remove the middle brace on the front of the trailer, the bed will mount right up. the drive shaft has about 4.5 inches or slip yoke travel. this will give you a little off center of the bed fender, but without a tape measure, you can't see it. the...

I would get the truck. Your student loans are low interest, and the truck will be worth more later as they become harder to find. feed your addiction. All being said, every one here would have told you to buy it had you not told us about your student loans. you financial status is none of...

i used a105a2 generator trailer. after you cut it down to what you want, you have a better bed than the a3. the a3 is only 34 inches wide and then you have the fenders sticking out the sides. the 105a2 gen trailer gives more options. the 105a3 is a rarer trailer and harder to get parts for...

I put a splitter on the relay under the the dash and hooked it up there. works great and you get to keep the electrical system weather proof

bob tailing a deuce and will be installing a m105 trailer bed in it. has any one done this with the original drive shaft and how did it work out for you. I reserched the XM381 and wheel base is 135" this is 5 longer than the wheel base for a deuce from the center of the front tires and the...

pm me with your address

just drill a hole in the bottom and let the rain run out

the tm states the oil pressure is to be 35psi or higher . if not , the vehicle is NMC. i dont think the sending unit is the same, but i don't have one here to make the comparison.. it could also be a short or the wire is frayed. had a similar problem with me truck.. terminal was loos and...

when you take out the studs, put them in a plastic bag and place them in the freeze. put the hub in the sun and let them cure over night. when you put them back together, the studs will be easeir to install. i used a couple of 4x4's and a BFH. worked like a charm

did you lengthen the drive shaft and if so how much??

wouldn't it be easier to just find some A3 rims and put the big tire on them. wait, that is what i did!!!!

I think we need to be realistic and understand that most of us will NEVER load 5000 lbs of stuff in our trucks and drive cross country to some far off destination and return empty. the nice thing about the m35a2 engine is it is a simple to maintain power plant that for the most part will still...