Search results

any idea of what size that hose is.. im in the process of cloecting all the parts to replace my radiator. just wann be sure i got all befor i do it. .. im not one for starting at job then having to stop an go run to the parts store so any help with the size ofthat would be great . thanks

just need a fast answer looked around a lil bit but didnt see what im looking for... so dose anyone know what size the front wheel studs are on a m1009. a part number or link would be killer. im pretty sure its a 7/16-20 but not positive an im not sure on length. any help would be great thanks,

also i have none of the black out lights or switches. all that was gone when i got the truck. ive had the truck for 5 years an never had anything like this happen. ive replaced the bulbs befor when needed with no problems. so any help whould be great.

well all i did was put a new bulb in an make sure all grounds were tight. so went back around checked all grounds agin but this time after doing that started up the truck an got no lights at all in any way. so turn it off checked fuse box all was good there. so im lost now

ok all i did some looking around didnt find anything like this.... got a m1009 with all lights on when you put the right turn signal on its setting off the revers lights. i opend up the light needed a bulb replaced it. tracked all grounds all are good. checked all fuses an were good. now after...

glow plugs.....

wow thanks for nothing ........ that was the first thing i did.

ok peolpe. heres what i got. 86 m1009. headlight work fin on low beam but when i hit them to go to high beam the passenger side goes out and just the driver side will go to high. so im just looking for any ideas of what may cause this or where i should start looking for fix the problem.

this forem has reall gone to **** noone can give an answer to anything they rather run there mouth abut spelling an **** that has nothing to do with the topic being asked about if you dont got anything to say regarding whats being asked dont say a thing..... moste of you probably are just...

thisi s what iwas thinking too. but wasnot sure if it would be the master or the hyrdoboost sence if im coreect the hyrdoboost it the one right agenst the firewall.

well its been about 3 mounths no problems till now.... i have fluid dripping dont on the my floor boards an the pedal is super soft agin.

all im saying is RUST lot and lots of RUST and years of offroading.

bolth rear wheel cilnders were shot. so i replaces everything drove for a few miles and BAM blew a line along the fram rail. soooo new question what size is the hard line that runs along the frame. thanks Ryan

funney i never seaid i was still driveing it but you all assume that i am. all i was asking was for a good starting point and that was it.

ok guys on my m1009 the other night was driving came to a stop and the parking breaklight came on and right after that my break pedal got reallyreally soft almoste hits the floor now when you push it. the light has been on ever sence none of the breaks are locked just got a super soft pedal now...

i dont think its the started it dosent sound like its engaged when the truck is running. i think in the am im gona drop it see if i can see anything. any other ideas would be great thanks

ok guys so i got around to looking at the truck today i wiped everything as clean as i could get it and toped off the oil. i started it let it run for a good 20 min and i dont see any oil dripping only this i see dripping if fuel (withch i knew about alredy) i do see alot of white smoke coming...

ya id say there is a good 3qts under it right now if not more. i can tell its something on the passenger side its the only side of the block and front axle that is covered. i just did a rear main on it in july an new oil pang gasket. i havent had any leaks or problems til now.

ok guys i got a m1009 and it is pissing oil everwhere. the hole passenger side is covered in oil all the way back to the tail gate. the hole under side of the truck is soaked on the passenger side. the drive side is dry. ive lookd everwhere i could today out in the -10 weather and cant seam to...

id say lmc (witch ive never had any problems with anything frome them) or classic parts