Search results

When I bought my M-1028 the P/O said he was paying like $30.00 for tabs. But the DMV says because its over a 1 ton its not considered a passanger vehicle so I have to pay more :cookoo: So they charge me $280.00 just for the tabs :shock: Then I had to buy 1 ton plates (witch is kind of...

Since I bought my truck the wipers have been slow and stop at random. Yesterday they finally quit working at all. So i took my test light and checked for power to the wiper motor. With the key on and the wipers on high I only have 2 wires that are hot. .8 WHT-93 A --- going to the suppressor...

Anyone know where to get the poppet drain from the bottom passanger side of fuel filter base? Ive been to every auto store in town and came up dry. I thought about useing a standard 3/8 corse thread break bleeder but the thread are .20 '' bigger. Edit: The first place i checked was the...

What is the middle fuel line on the sending unit for? The P/O just stuck a bolt in the end of the line. I only have 2 lines going to the engine, is the 3rd just a breather? If so should i take the bolt out and just let it dangle off the frame?

Has anyone ever installed one of these in there trucks? It folds down into the bumper:jumpin::jumpin::jumpin: *A-2000 Fold-A-Way Bumper Crane - Specifications

What is max RPM for a 1028? I have a 700r4 with 4:56 the RPM calculator says @ 65 mph 4th gear is 1884 RPM. and 3rd gear is 2692 RPM.

Don't want to start a new thread but im on my phone and this is my only internet access right now and searching all over on a tiny screen sucks...so my ponder is, is it normal for my crank pullyy to be able to turn by hand. Im changing the torsion damper and it is turning pretty easy...I would...

Where the heck is this vac line supos to go i was working on timing the m1028 and found that somone just threaded a bolt in the end.

my tranny guy just put the 700r4 in my 1028 but he didnt adjust the transfer case linkage,so my transfer case was in 4 high and the hubs were not locked. Not knowing this i drove it down the highway about 30 mile @ 70 mph. According to him my transfer case did not get damaged. Is there anything...

I have a question about my m1028 rear axle..my rear passanger tire moves in an out.when i jack the rear end up and push the tire it slides in about a 1/8 inchI looked under and the drum is moving with the tire...(lugs are tight ) my rear driver side tire does not do this...would this be a bad...

when my truck is idleing i have allways had a vibration inside my cab. this morning coming home from work, i was at a stop sign and the vibration got real bad. kinda sounded like i was driving on a rumble strip...i gave it a little gas and the vibration goes away,but when it just idles it...

I got back from out of town and my M1028 fires right up, I went to fuel it up its been below zero so i figured id put # 1 in...Ran fine on a 120 mile trip. next morning it turned over but wasnt firing. After awhile i gave it a little squirt of starting fluid and it started and ran fine. So i...

I have a stupid question. My M1028 batterys are dead,so i bought a 24 volt 10 AMP charger-how do i charge them..will hooking the charger up to the front bat charge both batterys? thanks

Hey guys i have a 1948 willys i was told that it was an old postal truck? ( not sure what do you think )... the motor i was told is a 1952...I striped the motor down to the block and am putting back together and need some bolt torqe specs. Anyone know what bolts need to be torqed to what ft.lbs...

I have this clunk in my truck everytime i let off the gas and get back on it. Its coming from the slop in my rear drive shaft, i can turn the drive shaft clockwise and counterclockwise a couple inches before it stops. anyone have this slop on there rigs,or know what this could be?

I'm woundering if the m1028 didnt have an air intake hose or if mine is just missing.

Hey guys finally figured out how to sync my dumb phone to my computer.Here is a pic of my first military vehicle : 1987 M1028 i bought a few months back. 21k miles

Sorry I know this has been asked before but i cant remember where i saw it... 1987 M1028 I cant remember what kind of Diffy lube im suppose to use. I bought Valvoline SYN power Full synthetic SAE 75W-90 and a tube of trans-X additive Is this the right stuff to put in the Front Diff? How much...

I was wondering if anyone has installed a remote start on there rigs? I have a M-1028 and would like to install one if possible. Does anyone have any tips for me if i can install this my-self or would it be a better idea to have a shop do this... I am mechanically inclined but have never...

Hey guys i had my steering colum apart on my 1987 M1028 and now when i put it back together it is able to shift gears when the key is not in.. I dont know if these CUCV trucks are spos to be like this or if I put it back together wrong..aslo i tryed looking in the manual for an exploded view of...