Search results

Definitely on my to do list coming up. They way I did it on my jk was I used heavy exhaust clamps to mount the shocks.

Eh I'm not into the whole green thing lol And yes the dash wasn't in quite right..... picture below posted. I put Nutserts in the dash and bolted it in then caulked the gap. It seals the light in much better and I'm going to paint it too. Also got my amp in the mail today and quick wired...

Ok so I guess the air system isn't that bad. In 24 hrs it leaked down to 60 psi from 120 psi. I can live with that considering before it leaked out in 20 minutes. Not much on the agenda for this weekend or the next week or two. I have to get a transmission in my brothers Yamaha raptor. But the...

There is a good thread some of us posted in that we made traction bars. Shouldn't be to far down the list

Yeah no problem sorry it took longer then I thought to get home I never left on time then

2 1/4"

I can check when I get home in 30 minutes

I'm thinking maybe a flow controller instead of pressure regulator.... That way you can keep the strength but slow the motion.

Here is a video of it plumbed and working. Just have to mount the cylinder and hook it to the lever. This cylinder is freaking strong. Way stronger then a normal push would be. I'm stoked how this is turning out. http://youtu.be/ydQHP4cgtuw

Air is finished pretty much. I need to run a new line to the air pack but I'll do that when I rebuild it. Also debating on putting a check valve in between the air compressor and tanks and a filter/water separator too. What do you guys think? I'm not going through the trouble of putting in a...

Man I'm sorry guys never got email notices people replied. I got my fittings from work. I work for a trailer company. We have everything and anything for dot air lines. As far as the behr paint Idk yet cause I haven't used it yet. Paint will be the last step for the truck. The chassis and...

Front end is done! Just needs paint. I got everything mounted and all new dot nylon air lines. I got all the fenders and head light assemblies lined up 10 times better then what they were. I'm so happy! The only thing I have to do is add the auxiliary air tank and plumb that and run a new air...

I was thinking about putting 6x9 in the cab corners and maybe 6 or 6.5 or maybe even 4x10 up above the windshield. 4x10 would work good but I'm not sure on sound quality from them.

Ok here's the other side.... It's all done finally. Fenders are back on but it started to pour so I didn't get pictures

I'm with you rusty..... I'm going the electric route though. Smaller lighter more compact. I'm hoping to sink a front and rear into the frame and the only thing you'll see will be fair leads.

Oh its going to be awhile. I'm hoping to have the front end on this weekend and painted underneath and the grill painted. Then one that's done the extended cab starts. I'm hoping to have it all done by the end of June beginning of July hopefully

The thickness I measured was .055". I used .049" sheet. I think they rot out because the water can get in where ever it wants too. The inside is completely open and it just collects and holds the water. Well find out tomorrow when I cut the rocker out of the passenger side.... yes co2 100% is...

This was all done with my Dewalt grinder send my Lincoln 140 amp mig welder on 110v. I love my little welder and it's good up to 5/16 to 3/8 material with multiple passes. 1/4 and thinner is good for single passes you just have to watch the duty cycle. I paid close to $600 for this setup with...

Rust Repair The weekend is here!!!!! So the rust repair begins!!!! OK so first off I took a ruler and marked out the part I wanted to cut out. Now to make your job as easy as possible cut square and straight as possible. Next using steady hands cut slowly and stay in your marks. After you get...

Actually I was wrong it will only be 3 switches one for pump and for each valve and the 4th light will be a tank low light.....