Search results

Well like you said just run it as a N/A motor. If it is not up armor the 6.5 will move it just fine.

it wont. you need the van or Military turbo set up.

Yeah that's me.... I'm getting shipped home in a couple months and don't want to take it with me.

well a th350 will hold up for about a month in a 10K pound truck. Your just going to burn that up. If you get a th400 and build it, it should hold up but you might want to think about a 4 speed like a 4L80 or a built 700R4. A 350SB will be a tad on the light side you might want to think about a...

I never needed anything but "stranded" tools to replace the pumps. Another thing you can do is get a engine off GL.. I got two new 6.2's for 150 bucks. I gave Mang one of the pumps and he says his 09 has never ran better. 400 Bucks man I tell ya that's a lot to pay for a pump. and here is a...

$400! get one off ebay new for a lot less! And there ez to get out, I can have them out in 30 min or less. Take off intake, take off lines at injectors, take oil fill tube out, remove the 3 bolts on the front gear. you will have to rotate the engine to get at each bolt. done

The military set up are as rare as hens teeth. I will be starting on my M211 resto in a couple months and I plan on finding a Dual civy unit. I think the way to go is hit the books and search the A1 Cardone catalogs

well then use grade 5. Your not going to brake grade 5 unless you smash it up good and even if you replaced it with "factory" rivets and hit the same thing its going to bust. Just put 5 in it and be done.

yeah you can install it.. .... Try to find one first.

yeah like asking what size bolt fits for something.. really.. are we all that lazy? but really I would ask if that were happening to me... the glow plugs are not something to just let to go to hell. There is a temp sending unit on the driver rear of the cylinder head (top) and one on the...

Go to the hardware store and get a bolt that fits. I would use grade 8 but I'm sure 5 would work just fine.

6.5 6.5L Chevy GM "Marine" Diesel Fuel Injector Nozzles:eBay Motors (item 350243817163 end time Sep-22-09 19:29:11 PDT) and http://shortlinks.net/ifv541 make sure to contact them first to make sure you get the correct injector. As of not rebuilding them your self.... I think we all...

yes they are the same. The thing to do is rebuild them. If you can take them out of the head you are smart enough to rebuild them. the rebuild kits are found on ebay and if you want i can get you the listing. All you have to do is remove the injector from the engine, unscrew it (it come apart)...

yeah there are 24 volt stuff in the truck and your better off with the 24v to 120. you can tie in to 24v off the junction block on the fire wall on the right side. But you do have 12v there too, there not a full 24v truck. All the driving lights and dash lights, heater blower ect are 12v. You...

why do you need a 24V pump? you know the truck is all 12V but the starter and the black out lights right?

I have never seen any. You might be out of luck on that one.

Saturn Surplus --> Saturn Surplus on the Web! has all the hoses. I know I got a full set from them.

coolant temp sender in the back of the engine? Heater hose fittings in the engine? cross over pipe cracked or t stat housing leaking? could be a lot of things. wash it all down, put a tester on the radiator cap and pump her up. you will find the leak.

Ah ok.. I was about to say... any who that should work out nice. Sorry I can not be of any help in fitting the engine and trans. I'm sure someone know how to around here.

ok.. Why would you install a engine with less HP them what is in there? From what I have seen the 3-53 is around 114 Hp and the multi is at least 130 (and can be cranked up) Also the amount of low end torque in the 3-53 has to be a lot lower then the multi just due to the rotating mass fo the...