Search results

I would also say to check the bearings. I did a little seal replacement write up a little while back where I had a leaking seal on my M1008. You should be able to find it pretty easy, it was about a month ago. In the write up I list part numbers and where to get some of the parts. I don't know...

Is the humming noise only present when 4 wheel drive is engaged? When you replaced the front output seal, metal one, was there also a little rubber washer that fits inside the spline area on the yoke?

I cannot swear that this will fix your leak but it worked for me so I wanted to share. Please don't bomb me for the lack of pics LOL. My computer gets all tied up when I try and upload them so I just chose not to even try this time. My transfer case was leaking around the output shaft and...

Looks good so far. I will be following the thread to see the progress.

Oh..... Gotcha. As far as I can see the easiest way to accomplish this would be to source some thick wall square tubing that just did fit over the extension tubes. Weld some on the top of your mount to fit the front detentions and then weld some on the bottom to fit the rear detentions. This...

The way this mount is secured is with bolts. Basically if your standing over it looking down there is a bolt that goes through the truck frame extender and then through the winch bracket or mount. Its not a lock but it would take some time to unbolt. The bolts also help steady up the mount so...

I have a set of Goodyear MTR's and a set of BFG Baja TA's. Both 37 X 12.50 X 16.5. I love them, they make the truck look so much better than the little stock tires. I had the option of using the HMMWV wheels and declined due to the need to modify or use spacers. I purchased 16.5 X 9 3/4...

Greg, I was unaware of the difference but you are correct. I just measured mine and it is 31 3/4 outside to outside on the front and 32 3/4 outside to outside on the rear. I just assumed they were the same. The inside of my mount is 32 inches which gives just a little play when you and your...

I really have no idea what the issue is. My father gave it to me and said it had a bad solenoid and he just did not want it anymore so I took it and placed it on a shelf for the TO DO SOMEDAY SOON. Thanks for the offer on the solenoid, I will let you know if I need it OR if mine craps out I...

Here is another pic of the whole assembly

This is the winch mount I have for my truck. It was fabed by a local welding machine shop for my dad and he gave it to me many years later. Not sure what it cost to have it made. Its very heavy. I have yet to install it on my truck due to some problems with the winch solenoids. Just wanted...

My lift is 2 1/2 inches with slight fender trimming. Rubs pretty easy. Going to a 6 inch lift soon

New tires and wheels I just put a set of BFG Baja T/A on my truck with new wheels. Looks so much better to me. Tire size is 37X12.50X16.5 military surplus.

Have fun breaking the king pins loose. I had a 3/4 inch breaker bar that is 3 foot long with a 3 foot cheeter pipe on it. When the king pin broke loose it sounded like a 22 rifle going off. I posted some info on SS about what I did when I went through mine. Just a suggestion here: The axle...

Does anyone have any information on the shackle flip from DIY4X verses the offroad design one. The are pretty close in price. I am just wondering if anyone has seen both in person and would rate one over the other as better built. I am also about the have both u joints in my rear driveshaft...

I think it looks great, I am going to do the bed soon in my truck and I think I will go with the OD green textured for the bed. I am also going to do the interior floor in the textured OD Green.

According to the artic fox web site the heaters, when properly installed they may be operated continuously and typical operation time is 3 to 5 hours. It also talks of setting them up on a timer.

I sure wish I could find the banks part so I could do somthing similar, The junk yards around here are few and far between. Anyone have a suggestions on sourcing the needed part?

Thanks, great work.

Great looking truck, just shows me how much I need to do.